DS-3E1506P-EI/M
4-Port Gigabit Smart PoE Switch
- 4 Gigabit PoE ports, 45 W
- 2 Gigabit uplink ports
- PoE watchdog restarts frozen cameras
- VLAN and loop prevention
DS-3E1506P-EI/M
4-Port Gigabit Smart PoE Switch
- 4 Gigabit PoE ports, 45 W
- 2 Gigabit uplink ports
- PoE watchdog restarts frozen cameras
- VLAN and loop prevention
Smart PoE Switch
Hikvision DS-3E1506P-EI/M 4 Port Gigabit Smart POE Switch
Ports
4 × Gigabit PoE port, 2 × Gigabit RJ45 port
PoE Standard
IEEE 802.3at/af standard for PoE ports.
PoE Power Budget
Total PoE Power Budget 45W
Network Parameters
MAC Address Table: 2K, Switching Capacity: 14Gbps, Packet Forwarding Rate: 10.42Mpps
Software Function
Support 802.1Q VLAN, Support PoE watchdog, Support STP/RSTP Loop prevention
Key specs
- 4 × Gigabit PoE ports, 2 × Gigabit RJ45 uplinks
- PoE budget 45 W
- PoE watchdog; cable detection
- 802.1Q VLAN, STP/RSTP loop prevention
- Switching capacity 14 Gbps
- 6 kV surge protection; 54 VDC
|
Network Parameters |
|
|
|
Ports |
4 × Gigabit PoE port,2 × Gigabit RJ45 port |
|
|
MAC Address Table |
2 K |
|
|
Switching Capacity |
14 Gbps |
|
|
Packet Forwarding Rate |
10.42 Mpps |
|
|
Internal Cache |
1 Mbits |
|
|
PoE Power Supply |
|
|
|
PoE Standard |
IEEE 802.3af,IEEE 802.3at |
|
|
PoE Power Pin |
End-span: 1/2(-), 3/6(+) |
|
|
PoE Port |
PoE: Ports 1 to 4 |
|
|
Max. Port Power |
30 W |
|
|
PoE Power Budget |
45 W |
|
|
Software Function |
|
|
|
Long Range |
Ports 1 to 4: up to 300 m. Long range performance may vary depend on camera model or cable condition. |
|
|
Port Isolation |
Ports 1 to 4: port isolation mode to improve network security Ports in an isolation group cannot communicate with each other, but they can communicate with ports outside the isolation group. |
|
|
PoE Watchdog |
Ports 1 to 4: auto detect and restart the cameras that do not respond. |
|
|
Link Aggregation |
Link aggregation is used to aggregate multiple physical ports to form a logical port for load balancing, bandwidth expansion, and port protection. Support static link aggregation. Support 2 aggregation groups. |
|
|
Loop Prevention |
Loop prevention is used to prevent the switching network from forming loops, which will seriously affect network communication. Disabled by default. Support 802.1D STP. Suppport 802.1w RSTP. |
|
|
VLAN |
VLAN is used for network scale planning and network health improvement. Support 802.1Q. Configurable VLAN ID from 1-4094. Support Trunk, Access port mode. Support Max. 32 VLAN. |
|
|
HPP |
Support one-click activation and remote management via Hik-Partner Pro. Functions supported: Display the port rate. Display the port bandwidth utilization rate. Display the PoE power usage. Display topology information. Display the alarm status. Restart ports and devices. Enable port long-rage mode. Remotely upgrade the device. |
|
|
System Maintenance |
Support device management via web. Support DHCP Client. Enabled by default for dynamic assignment of management IP addresses. Support Super IP, which is a fixed IP address (10.180.190.200) for direct access. Support management via Hik-Central Pro. Support remote management via Hik-Partner Pro. Support cable detection. Abnormal open circuits and short circuits as well as network cable length can be detected. Supports 802.1ab LLDP for peer device discovery. Support SNMP v1/v2c for third-party management platform access. Support port mirroring for fault locating. |
|
|
General |
||
|
Shell |
Metal material |
|
|
Net Weight |
0.27 kg (0.6 lb) |
|
|
Gross Weight |
0.77 kg (1.7 lb) |
|
|
Dimensions (W × H × D) |
121.1 mm × 27.6 mm × 83.1 mm (4.77'' × 1.09'' × 3.27'') |
|
|
Operating Temperature |
0 °C to 40 °C (32 °F to 104 °F) |
|
|
Storage Temperature |
-40 °C to 85 °C (-40 °F to 185 °F) |
|
|
Operating Humidity |
5% to 95% (no condensation) |
|
|
Relative Humidity |
5% to 95% (no condensation) |
|
|
Power Supply |
54 V DC, 0.92 A |
|
|
Installation Mode |
Desk-Mounted,Wall-Mounted |
|
|
Max. Power Consumption |
50 W |
|
|
Power Consumption in Idle |
1.8 W |
|
|
Surge Protection |
6 kV |
|
|
Approval |
||
|
EMC |
CE-EMC (EN 55032: 2015+A11: 2020, EN IEC 61000-3-2: 2019, EN 61000-3-3: 2013+A1: 2019, EN 50130-4: 2011+A1: 2014, EN 55035: 2017+A11: 2020) |
|
|
Safety |
CB (AMD1:2009, AMD2:2013, IEC 62368-1: 2014 (Second Edition) |
|
|
Chemistry |
Reach (Regulation (EC) No.1907/2006),WEEE (2012/19/EU),CE-RoHS (2011/65/EU) |
|
Know before you buy
Quick answers about the DS-3E1506P-EI/M, and how it compares.
How many cameras can this PoE switch power?
Two limits apply: the number of PoE ports, and the total PoE budget in watts. Add up the maximum power of each camera from its datasheet and keep about 20% spare. Example: 16 cameras at 6 W each need 96 W, plus 20% is about 115 W, so a switch with a 125 W budget or more is right. A PoE port (802.3af) gives up to 15.4 W and a PoE+ port (802.3at) up to 30 W. PTZ cameras and cameras with heaters, strong IR or strobe lights need PoE+ or Hi-PoE (802.3bt). Not sure? Send us your camera list and we size it for you.
Unmanaged, smart or managed switch: which one do I need?
Unmanaged switches are plug and play, with nothing to set up: good for small systems. Smart (web managed) switches add a web page and app view for VLANs, port status, cable checks and, on many models, PoE watchdog, so you can find and fix problems from your desk. Managed (Layer 2+ or Layer 3) switches add full control, routing and ring protection for large sites, campuses and city projects. For most CCTV jobs with 8 to 48 cameras, a smart PoE switch is the best value. Ask us if you are not sure.
Can I buy this online?
Hikvision security products are installed products, so we start with a free pre-sales consultation: our engineers suggest the right model and everything that goes with it for your site and send a quote. Use Request a Quote on this page, contact us or WhatsApp +92 300 ESCO 301. Offices in Karachi, Lahore, Islamabad and Rawalpindi. 1 year carry-in warranty.