Skip to Content

Arriving

IX30:4

A 3,000 W, 4-channel networked DSP amplifier for installed sound: powerTANK shares the power across channels, Lo-Z or 70/100 V per channel, 12 x 12 matrix, 8 x 8 Dante, SONICUE. Scroll down for details.

Rs. 0 Rs. 0

  • Brand - Dynacord
Dynacord
Dynacord

German Pro Audio excellence, powering concerts, venues, and global events.

Dynacord IX30:4
4-Channel Networked DSP Power Amplifier

Drive low-impedance or 70/100 V loudspeakers with 3,000 W of total shared power. Mix and route analog and Dante audio with the built-in DSP, and configure the system in SONICUE.

  • 3,000 W Total powerTANK Output
  • 96 kHz DSP & 12 × 12 Matrix
  • 8 × 8 Dante Audio
Dynacord IX30:4 networked DSP power amplifier, angled, front and rear views

Dynacord IX30:4 capabilities

The IX30:4 combines 3 kW of total amplification, mixing and system control in a single rack unit (1 RU).

  • Share power and reduce idle consumption

    powerTANK shares the total output budget across channels so higher-demand loads can draw more power within their limits. ecoRAIL reduces idle consumption to 26 W in Idle/Eco mode (output below 1 W).

  • Drive different speaker loads

    Select Lo-Z or 70/100 V direct drive per channel. Drive 100 V speaker lines without bridging.

  • Mix and tune audio onboard

    Route sources in the 12 × 12 matrix mixer, add built-in stereo effects and tune loudspeaker outputs with EQ, delay and FIR-Drive.

  • Bring analog sources onto Dante

    Connect to the network through 8 Dante inputs and 8 Dante outputs. Use the 4 mic/line inputs as Dante break-in points for local audio sources.

  • Keep audio signals available

    Pilot-tone monitoring can switch to a configured backup audio source. During AC loss, ghostPOWER via PoE on the Primary port keeps DSP, Dante and mic/line inputs active. Speaker outputs require AC power.

  • Automate and control in SONICUE

    Use the integrated MXE-style TaskEngine to automate and schedule actions and integrate third-party devices. Give staff local control through a compatible WPN1 or TPC-1 panel.

Where the Dynacord IX30:4 Is Used

The IX30:4 combines amplification, DSP and audio routing for venues with multiple loudspeaker zones.

Estadio Más Monumental stadium in Buenos Aires

Sports Venues

Route match-day announcements to seating areas and send a separate music feed to concourses. Allocate amplifier power according to each zone’s loudspeaker load.

All Saints Church in Crowborough

Houses of Worship

Mix microphones and music with the onboard DSP. Send separate feeds to the main worship space and overflow rooms.

Cavatina Hall performing arts venue in Bielsko-Biała, Poland

Live Performance Spaces

Route stage and playback sources to the main loudspeakers and fill zones. Adjust EQ and delay for each output to suit the room.

dynacord-ix-series-brochure.pdf
Download
dynacord-ix-series-eu-declaration-of-conformity.pdf
Download
dynacord-ix-series-installation-manual.pdf
Download
dynacord-ix30-4-datasheet.pdf
Download

Key specs

  • 4 amplifier channels with 3,000 W total shared power via powerTANK
  • Low-impedance and 70/100 V direct drive selectable per channel
  • 96 kHz DSP with a 12 × 12 matrix mixer, stereo effects and FIR-Drive
  • 8 × 8 Dante audio and 4 mic/line inputs
  • Pilot-tone input monitoring with automatic switchover to a configured backup source
  • SONICUE control and TaskEngine automation
  • ghostPOWER via PoE keeps DSP, Dante and mic/line inputs active during AC mains loss
  • 19-inch, 1 RU rack format
Chat on WhatsApp

Dynacord IX30:4 | Technical Specifications


Product Identification

SpecificationValue
BrandDynacord
ModelIX30:4
SeriesIX Series
Product type4-channel networked DSP power amplifier
Order numberF.01U.411.087

Output Power

LoadAll 4 channels equally driven, per channelMaximum single-channel outputBridged output
2 Ω750 W1,000 W1,000 W
2.7 Ω750 W800 W1,300 W
4 Ω600 W600 W1,500 W
8 Ω750 W1,000 W1,200 W
70 V direct drive750 W750 W—
100 V direct drive750 W1,000 W—

Amplifier Performance

SpecificationValue
Output stageFixed-frequency Class D
Voltage gain32 dB nominal, adjustable from 20 to 44 dB in Lo-Z mode at 1 kHz
Direct-drive input sensitivity+6 dBu (1.55 V), fixed
Frequency response20 Hz–20 kHz (±1 dB), analog input to speaker output
THD+N<0.1% at 1 kHz, 3 dB below maximum output, AES17
Crosstalk<−80 dB at 1 kHz, 12 dB below maximum output into 8 Ω
Damping factor>250 at 20–200 Hz into 8 Ω
Output noise, analog input<−67 dBu, A-weighted in Eco mode
Output noise, digital input<−70 dBu, A-weighted in Eco mode

Digital Signal Processing

SpecificationValue
Sampling rate96 kHz internal DSP, switchable 48/96 kHz Dante
Latency0.77 ms from analog input to speaker output
Matrix mixer12 × 12 with stereo effects
Input processingHigh-pass filter, 4 selectable filters per channel, noise gate, compressor or AGC, and input pilot-tone supervision
User processing12 EQ filters per channel and 0–2,000 ms delay
Array processing5 EQ filters per channel and 0–500 ms delay
Speaker processing10 EQ filters per channel, high-pass and low-pass crossover filters, and 0–20 ms alignment delay
Speaker FIRUp to 1,025 taps
Speaker limitersPeak Anticipation Limiter and RMS/TEMP Limiter per channel
Load supervisionPilot tone up to 30 kHz, impedance measurement and load monitoring
Source failoverPilot-tone supervision on analog and Dante inputs, with switchover to a configured failover source
DSP presets1 factory preset and 20 user presets

Audio Connectivity

SpecificationValue
Mic/line inputs4 channels on 2 × 5-pin male Euroblock connectors
Input gain0–60 dB
Maximum input level+18 dBu balanced, +12 dBu unbalanced
Phantom power+48 V, switchable per input
Balanced input impedance>10 kΩ
Equivalent input noise−127 dBu, A-weighted at 150 Ω
Digital input reference+22 dBu for 0 dBFS
Speaker output connector1 × 8-pin Euroblock
Speaker cable conductor size2.5 mm² / 12 AWG

Network & System Control

SpecificationValue
Network ports2 × RJ45
Ethernet1000BASE-T / 100BASE-TX with integrated switch
Network audio8 Dante inputs and 8 Dante outputs at 48 or 96 kHz
Network redundancyGlitch-free Primary/Secondary mode or RSTP
Remote controlOCA/AES70 and SONICUE Sound System Software
System automationIntegrated TaskEngine for scheduling, control logic and third-party device integration
SONICUE Control ServerSupports direct use with compatible WPN1 and TPC-1 controllers
ghostPOWER backupIEEE 802.3af PoE on the Primary port keeps DSP, Dante and mic/line inputs active during AC mains loss

GPIO & Indicators

SpecificationValue
GPIO control port3 channels, each configurable as analog input, digital input or digital output
Control port connector1 × 8-pin male Euroblock
Analog input range0 to +13 V, 133 kΩ input resistance
Digital input thresholdsON below 1.5 V, OFF above 2.0 V, with internal 10 kΩ pull-up to 10 V
Digital outputON switches to ground, maximum 200 mA. OFF is open collector.
Reference voltage output+10 V, maximum 200 mA, supervised and short-circuit protected
Ready/Fault relayGalvanically isolated, maximum 30 V DC / 500 mA
Front indicatorsPower, Standby, Fault, OMNEO, PoE and AC LEDs, plus signal/peak LEDs for each mic/line input and amplifier output
Rear indicators and controlInfo and Status LEDs, plus recessed INIT button

Electrical

SpecificationValue
AC mains input100–240 V AC, 50–60 Hz
Mains connectorIEC C14
Rated power consumption550 W
Idle/Eco mode26 W at output power below 1 W
Standby consumption<15 W
Power supplySwitch-mode supply with digitally controlled power factor correction
ProtectionsAudio limiters, high temperature, DC, HF, short circuit, back-EMF, peak current, inrush current, mains current, and mains overvoltage/undervoltage
IEC protection classClass I, grounded

Mechanical & Environmental

SpecificationValue
Rack format19-inch, 1 RU
Dimensions (W × H × D)483 × 44.1 × 447 mm
Net weight7.5 kg
Shipping weight9.3 kg
FinishBlack
CoolingFront-to-rear airflow with supervised, temperature-controlled fans
Operating ambient temperature+5 °C to +40 °C
Electromagnetic environmentsE1, E2 and E3
Questions & answers

Know before you buy

Quick answers about the IX30:4, and how it compares.

What is the Dynacord IX30:4?
The Dynacord IX30:4 is a 4-channel networked DSP power amplifier for installed sound systems. It combines 3,000 W of shared output power, a 12 × 12 matrix mixer and 8 × 8 Dante audio in a single rack unit.
Can the IX30:4 drive low-impedance and 70/100 V loudspeakers at the same time?
Yes. Each channel can be configured for low-impedance or 70/100 V direct-drive operation. That lets one amplifier serve zones with different loudspeaker loads, within the channel limits and shared power budget.
Can the IX30:4 work directly with a Dynacord WPN1-EU wall panel?
Yes. The IX30:4 can act as a SONICUE Control Server for the WPN1-EU. The wall panel can give staff access to controls configured in SONICUE, such as zone volume and source selection.
What is the difference between the Dynacord IX30:4 and IX15:4?
Both models have four amplifier channels, a 12 × 12 matrix mixer and 8 × 8 Dante audio. The IX30:4 offers 3,000 W total shared power, compared with 1,500 W for the IX15:4. Check the output rating at your intended speaker load when choosing between them.
Can the IX30:4 switch to a backup audio source if the main feed fails?
Yes. Pilot-tone supervision can monitor an analog or Dante input and trigger a switch to a configured backup source when the monitored pilot tone is lost.
Will the Dynacord IX30:4 keep playing through its speakers if AC power fails?
The speaker outputs need AC power. If the Primary network port is connected to an active IEEE 802.3af PoE source, ghostPOWER keeps the DSP, Dante network and mic/line inputs active during an AC outage.
Who is the authorized Dynacord distributor in Pakistan?
Electronic Security Company (ESCO) is an authorized Dynacord distributor in Pakistan. Contact ESCO for the Dynacord IX30:4 price in Pakistan, current availability, lead time or a project quotation.
Similar Products
Accessory Products
Chat on WhatsApp
WhatsApp