Skip to Content

AV-MT300-W
AV-MT300-W
MXE5-64
MXE5-64
Arriving

IX15:4

The Dynacord IX15:4 is a 4-channel networked DSP power amplifier for installed sound systems, with 1,500 W of total power shared across its outputs via powerTANK. It combines a 12 × 12 matrix mixer, 96 kHz DSP, 8 × 8 Dante audio and four mic/line inputs in a single rack unit. Use SONICUE Sound System Software to configure and control the amplifier.


Rs. 0 Rs. 0

  • Brand - Dynacord
Dynacord
Dynacord

German Pro Audio excellence, powering concerts, venues, and global events.

Dynacord IX15:4
4-Channel Networked DSP Power Amplifier

Drive low-impedance or 70/100 V loudspeakers with 1,500 W of total shared power. Mix and route analog and Dante audio with the built-in DSP, and configure the system in SONICUE.

  • 1,500 W Total powerTANK Output
  • 96 kHz DSP & 12 × 12 Matrix
  • 8 × 8 Dante Audio
Dynacord IX15:4 DSP power amplifier, angled, front and rear views

Dynacord IX15:4 capabilities

The IX15:4 combines 1.5 kW of total amplification, mixing and system control in a single rack unit (1 RU).

  • Share power and reduce idle consumption

    powerTANK shares the total output budget across channels so higher-demand loads can draw more power within their limits. ecoRAIL reduces idle consumption to 26 W in Idle/Eco mode (output below 1 W).

  • Drive different speaker loads

    Select Lo-Z or 70/100 V direct drive per channel. Drive 100 V speaker lines without bridging.

  • Mix and tune audio onboard

    Route sources in the 12 × 12 matrix mixer, add built-in stereo effects and tune loudspeaker outputs with EQ, delay and FIR-Drive.

  • Bring analog sources onto Dante

    Connect to the network through 8 Dante inputs and 8 Dante outputs. Use the 4 mic/line inputs as Dante break-in points for local audio sources.

  • Keep signal processing active

    With PoE on the Primary network port, ghostPOWER keeps DSP, Dante and mic/line inputs active during an AC outage. Speaker outputs require AC power.

  • Automate and control in SONICUE

    Use the integrated MXE-style TaskEngine to automate and schedule actions and integrate third-party devices. Give staff local control through a compatible WPN1 or TPC-1 panel.

Explore the Dynacord IX15:4 in 360°

Take a closer look at the 1 RU rack-mount chassis, front-panel status LEDs and rear audio, network and loudspeaker connections.

  • 1 RU Rack-Mount Chassis
  • Front Status LEDs
  • Rear Connections

Where the Dynacord IX15:4 Is Used

The IX15:4 combines amplification and audio routing for venues that need to manage multiple loudspeaker zones.

Estadio Más Monumental stadium in Buenos Aires

Sports Venues

Route announcements and music to different speaker zones, with output power allocated according to each zone’s loudspeaker load.

All Saints Church in Crowborough

Houses of Worship

Mix microphones and music on the built-in DSP and route separate feeds to the main worship space and overflow rooms.

Grand Hyatt Barcelona hospitality venue

Hotels & Restaurants

Manage background music across lobbies and dining areas. Use low-impedance loudspeakers in one zone and 70/100 V distributed loudspeakers in another.

dynacord-ix-series-brochure.pdf
Download
dynacord-ix-series-eu-declaration-of-conformity.pdf
Download
dynacord-ix-series-installation-manual.pdf
Download
dynacord-ix15-4-datasheet.pdf
Download

Key specs

  • 4 amplifier channels with 1,500 W total shared power via powerTANK
  • Lo-Z and 70/100 V direct-drive outputs
  • 96 kHz DSP with a 12 × 12 matrix mixer and FIR-Drive
  • 8 × 8 Dante audio and 4 mic/line inputs
  • SONICUE control and TaskEngine automation
  • ghostPOWER via PoE keeps DSP, Dante and mic/line inputs active during AC mains loss
  • 19-inch, 1 RU rack format
Chat on WhatsApp

Dynacord IX15:4 | Technical Specifications


Product Identification

SpecificationValue
BrandDynacord
ModelIX15:4
SeriesIX Series
Product type4-channel networked DSP power amplifier
Order numberF.01U.411.024


Output Power

LoadAll channels equally driven, per channelMaximum single-channel outputBridged output
2 Ω375 W1,000 W750 W
2.7 Ω375 W800 W750 W
4 Ω375 W600 W750 W
8 Ω375 W1,000 W750 W
70 V direct drive375 W750 W

100 V direct drive375 W1,000 W


Amplifier Performance

SpecificationValue
Output stageFixed-frequency Class D
Voltage gain32 dB nominal, adjustable from 20 to 44 dB in Lo-Z mode at 1 kHz
Direct-drive input sensitivity+6 dBu (1.55 V), fixed
Frequency response20 Hz–20 kHz (±1 dB), analog input to speaker output
THD+N<0.1% at 1 kHz, 3 dB below maximum output, AES17
Crosstalk<−80 dB at 1 kHz, 12 dB below maximum output into 8 Ω
Damping factor>250 at 20–200 Hz into 8 Ω
Output noise, analog input<−67 dBu, A-weighted in Eco mode
Output noise, digital input<−70 dBu, A-weighted in Eco mode


Digital Signal Processing

SpecificationValue
Sampling rate96 kHz internal DSP, switchable 48/96 kHz Dante
Latency0.77 ms from analog input to speaker output
Matrix mixer12 × 12 with stereo effects
Input processingHigh-pass filter, 4 selectable filters per channel, noise gate, compressor or AGC, and input pilot-tone supervision
User processing12 EQ filters per channel and 0–2,000 ms delay
Array processing5 EQ filters per channel and 0–500 ms delay
Speaker processing10 EQ filters per channel, high-pass and low-pass crossover filters, and 0–20 ms alignment delay
Speaker FIRUp to 1,025 taps
Speaker limitersPeak Anticipation Limiter and RMS/TEMP limiter per channel
Load supervisionPilot tone up to 30 kHz, impedance measurement and load monitoring
Source fallbackPilot-tone monitoring on analog and Dante inputs, with switchover to a configured failover source
DSP presets1 factory preset and 20 user presets


Audio Connectivity

SpecificationValue
Mic/line inputs4 channels on 2 × 5-pin Euroblock connectors
Input gain0–60 dB
Maximum input level+18 dBu balanced, +12 dBu unbalanced
Phantom power+48 V, switchable per input
Balanced input impedance>10 kΩ
Equivalent input noise−127 dBu, A-weighted at 150 Ω
Digital input reference+22 dBu for 0 dBFS
Speaker output connector1 × 8-pin Euroblock
Speaker cable conductor size2.5 mm² / 12 AWG


Network & System Control

SpecificationValue
Network ports2 × RJ45
Ethernet1000BASE-T / 100BASE-TX with integrated switch
Network audio8 Dante inputs and 8 Dante outputs at 48 or 96 kHz
Network redundancyGlitch-free Primary/Secondary mode or RSTP
Remote controlOCA/AES70 and SONICUE Sound System Software
System automationIntegrated TaskEngine for scheduling, control logic and third-party device integration
SONICUE Control ServerSupports direct use with compatible WPN1 and TPC-1 controllers
ghostPOWER backupIEEE 802.3af PoE on the Primary port keeps DSP, Dante and mic/line inputs active when AC mains is lost


GPIO & Indicators

SpecificationValue
GPIO control port3 configurable channels for analog input, digital input or digital output
Control port connector1 × 8-pin Euroblock
Analog input range0 to +13 V, 133 kΩ input resistance
Digital input thresholdsON below 1.5 V, OFF above 2.0 V, with internal 10 kΩ pull-up to 10 V
Digital outputON switches to ground, maximum 200 mA. OFF is open collector.
Reference voltage output+10 V, maximum 200 mA, supervised and short-circuit protected
Ready/Fault relayGalvanically isolated, maximum 30 V DC / 500 mA
Front indicatorsPower, Standby, Fault, OMNEO, PoE and AC LEDs, plus signal/peak indicators per mic/line input and amplifier output
Rear indicators and controlInfo and Status LEDs, plus recessed INIT button


Electrical

SpecificationValue
AC mains input100–240 V AC, 50–60 Hz
Mains connectorIEC C14
Rated power consumption300 W
Idle/Eco mode26 W at output power below 1 W
Standby consumption<15 W
Power supplySwitch-mode supply with digitally controlled power factor correction
ProtectionsAudio limiting, high temperature, DC, HF, short circuit, back-EMF, peak current, inrush current, mains current, and mains overvoltage/undervoltage
IEC protection classClass I, grounded

Mechanical & Environmental

SpecificationValue
Rack format19-inch, 1 RU
Dimensions (W × H × D)483 × 44.1 × 447 mm
Net weight7 kg
Shipping weight8.9 kg
FinishBlack
CoolingFront-to-rear airflow with supervised, temperature-controlled fans
Operating ambient temperature+5 °C to +40 °C
Electromagnetic environmentsE1, E2 and E3
Questions & answers

Know before you buy

Quick answers about the IX15:4, and how it compares.

What is the Dynacord IX15:4?
The Dynacord IX15:4 is a 4-channel networked DSP power amplifier for installed sound systems. It combines 1,500 W of total shared output power, a 12 × 12 matrix mixer, and 8 × 8 Dante audio in a single rack unit.
Can the IX15:4 drive both low-impedance and 70/100 V speakers?
Yes. Each channel can be configured for low-impedance speakers or 70 V or 100 V direct drive. This lets you use one amplifier for different loudspeaker loads across a venue.
Can the IX15:4 work directly with the Dynacord WPN1-EU wall panel?
Yes. The IX15:4 can act as a SONICUE Control Server for the WPN1-EU. Configure the panel’s controls in SONICUE to give staff access to settings such as zone volume and source selection.
How does powerTANK share 1,500 W across the four channels?
powerTANK lets channels with higher demand draw more from the shared 1,500 W power budget, within the output limits for each loudspeaker load. With all four channels equally driven, Dynacord specifies 375 W per channel for the loads listed in the datasheet.
What stays active when the IX15:4 loses AC mains power?
With IEEE 802.3af PoE connected to the Primary network port, ghostPOWER keeps the DSP, Dante network and mic/line inputs active. The speaker outputs still require AC mains power.
What should I include when requesting an IX15:4 project quotation?
Share the number of zones, the loudspeaker type and load per zone, and whether you need Dante audio or WPN1-EU wall control. Specify IX15:4, order number F.01U.411.024, when requesting this model.
Who is the authorized Dynacord distributor in Pakistan?
Electronic Security Company (ESCO) is an authorized Dynacord distributor in Pakistan. Contact ESCO for the IX15:4 price in Pakistan, stock availability, lead time or a project quotation.
Chat on WhatsApp
WhatsApp