Skip to Content

IX15:4
IX15:4
RE650
RE650
Rs. 22,000.00
Rs. 22,000.00
Arriving

MXE5-64

The Dynacord MXE5-64 is an open-architecture DSP matrix mix engine for installed sound systems. It combines audio mixing, signal processing and routing with 64 × 64 Dante network audio channels, 12 mic/line inputs and 8 line outputs. Use SONICUE Sound System Software to configure the system and TaskEngine to automate control tasks.
Rs. 0 Rs. 0

  • Brand - Dynacord
Dynacord
Dynacord

German Pro Audio excellence, powering concerts, venues, and global events.

Dynacord MXE5-64
DSP Matrix Mix Engine

Mix, process and route audio across multiple zones. Configure custom signal paths in SONICUE and automate scheduled actions and scene changes with TaskEngine.

  • 76 × 72 DSP Matrix
  • 64 × 64 Dante Channels
  • 12 Mic/Line Inputs and 8 Line Outputs
Dynacord MXE5-64 DSP Matrix Mix Engine

Dynacord MXE5-64 capabilities

  • Route audio by zone

    Use the 76 × 72 matrix to route foreground music and other sources independently to the main hall, lobby and additional zones.

  • Tune each output

    Tune loudspeaker outputs with EQ, delay and limiting. The DSP runs at 48 or 96 kHz with low processing latency.

  • Combine analog and network audio

    Use the open-architecture DSP to integrate analog sources and Dante or AES67 audio into a Dynacord system, with AES70/OCA for network control.

  • Schedule scene changes

    Use TaskEngine to recall audio scenes on a schedule for recurring events or changes in room use.

  • Build operator controls

    Design custom operator controls in SONICUE for TPC-1, WPN1 or the Panel Viewer app so staff can access the sources and levels they need.

  • Monitor the system

    Internal supervision and a watchdog monitor the processor. A fault output reports issues to external equipment, and redundant audio networking is supported.

How the MXE5-64 Automates Room Audio

Give staff a wall-mounted volume control for a single audio zone. Here’s how the MXE5-64 turns a knob adjustment into a change in that zone’s volume.

  1. Turn the wall control

    A staff member turns the volume knob. A configured analog GPIO input on the MXE5-64 reads the change.

  2. TaskEngine maps the input

    TaskEngine scales the GPIO input value to the DSP level range configured for that zone.

  3. The zone volume adjusts

    The MXE5-64 applies the new level to the assigned zone. Other zones keep their own settings.

Where the Dynacord MXE5-64 Is Used

Estadio Más Monumental in Buenos Aires

Stadiums & Sports Facilities

Route match-day announcements to seating areas and send separate music feeds to concourses and hospitality areas.

Cavatina Hall in Bielsko-Biała, Poland

Theatres & Performing Arts Centres

Send programme audio to the main hall and background music to the lobby, with independent level control for each area.

All Saints Church in Crowborough, England

Houses of Worship

Route speech and music to the main worship area and create a separate mix for overflow rooms.

dynacord-mxe-series-eu-declaration-of-conformity.pdf
Download
dynacord-mxe5-64-datasheet.pdf
Download
dynacord-mxe5-64-installation-manual.pdf
Download

Key specs

  • 76 × 72 Open-Architecture DSP Matrix
  • 64 × 64 Dante Network Audio Channels
  • 12 Mic/Line Inputs and 8 Line Outputs
  • 48/96 kHz DSP Processing
  • 8 Configurable GPIO Ports
  • SONICUE Control and TaskEngine Automation
  • 19-Inch, 1 RU Rack Mount
Chat on WhatsApp

Dynacord MXE5-64: Detailed Technical Specifications


System and Software

SpecificationValue
ModelMXE5-64
Product numberF.01U.424.586
Product typeOpen-architecture DSP matrix mix engine and system controller
Audio matrix76 inputs × 72 outputs
Free DSP configurationUp to 3,840 crosspoints and 256 signal paths
Configuration and controlSONICUE Sound System Software v1.4 or later
System automationIntegrated TaskEngine
System monitoringInternal supervision, watchdog and fault output

Analog Audio

SpecificationValue
Analog inputs12 electronically balanced mic/line inputs
Analog outputs8 electronically balanced line outputs
Audio connectors10 × 6-pole Euroblock, 2 channels per connector
Nominal input/output level+6 dBu (1.55 V)
Maximum input/output level+22 dBu (9.7 V)
Analog input gain0 to +60 dB
Phantom power+48 V, 10 mA, switchable per input
Input impedance2.2 kΩ
Output impedance47 Ω
Minimum load impedance600 Ω
Frequency response, analog input to output20 Hz–20 kHz at 48 kHz, or 20 Hz–40 kHz at 96 kHz, both ±0.5 dB
Signal-to-noise ratio, A-weighted>118 dB at analog input and output individually. >115 dB from analog input to analog output.
Equivalent input noise<−128 dB, A-weighted, 20 Hz–20 kHz
THD+N<0.002% at 1 kHz, 1 dB below maximum level
Crosstalk<−105 dB at 1 kHz, 1 dB below maximum level
Common-mode rejection>70 dB at 1 kHz, nominal level

Network Audio and Control

SpecificationValue
Dante network audio64 inputs × 64 outputs at 48 or 96 kHz
Dante flows64 receive and 64 transmit
Network audio compatibilityDante / AES67
Network control protocolAES70 / OCA
Ethernet ports3 × RJ45
Ethernet standards1000BASE-T / 100BASE-TX with integrated switch
Network redundancyRedundant audio networking supported

Digital Signal Processing

SpecificationValue
Sampling rates48 or 96 kHz, synchronized to OMNEO/Dante
DSP processors2 × SHARC ADSP-21469 at 450 MHz
Processing capacity900 MIPS, 5.4 GFLOPS
Internal processing32/40-bit floating point
Analog input-to-output latency<0.45 ms at 48 kHz, <0.22 ms at 96 kHz
Delay capacity348 seconds
FiltersParametric EQ, low-pass, high-pass, low/high shelving, crossover and FIR
DynamicsDucker, compressor, noise gate, AGC and ANC
LimitersPeak and RMS/temperature limiters
Mixing and routingRouter, matrix mixer and automatic mixer
Signal generatorsSine, pink noise and white noise
Pilot toneGenerator and detector with notch filter
DSP presets60

GPIO and Fault Signalling

SpecificationValue
Control connector15-pole Euroblock
Configurable GPIO8 ports, each configurable as analog input, digital input or digital output
Analog GPIO input0 to +11 V, 110 kΩ input resistance
Digital input thresholdsON below 1.5 V, OFF above 2.0 V. 10 kΩ internal pull-up.
Digital outputsOpen collector. ON switches to ground, up to 200 mA.
Reference voltage output+10 V, up to 200 mA, supervised and short-circuit protected
READY/FAULT contactGalvanically isolated relay, maximum 30 V DC / 500 mA

User Interface

SpecificationValue
DisplayMonochrome OLED, 256 × 64 pixels
Front-panel controlsUp, Enter and Down buttons
Front-panel indicators12 input signal/clip LEDs, 12 phantom-power LEDs, 8 output signal/clip LEDs, and Power, Standby, Fault and OMNEO status LEDs
Rear-panel controls and indicatorsMains switch and one status LED

Electrical

SpecificationValue
Mains supply100–240 V AC, 50–60 Hz
Mains connectorIEC appliance inlet
Power consumption50 W typical, 55 W maximum
IEC protection classClass I, grounded
ProtectionHigh-temperature and mains overvoltage/undervoltage protection

Mechanical and Environmental

SpecificationValue
Dimensions (W × H × D)483 × 43.5 × 471 mm
Rack mounting19-inch, 1 RU
Net weight6.0 kg
Shipping weight8.1 kg
ColourBlack
CoolingFront-to-rear airflow with a temperature-controlled fan
Operating ambient temperature−5 °C to +45 °C
Operating altitudeUp to 2,000 m
Electromagnetic environmentE1, E2 and E3
Questions & answers

Know before you buy

Quick answers about the MXE5-64, and how it compares.

What is the Dynacord MXE5-64 used for?
The Dynacord MXE5-64 is a DSP matrix mix engine that mixes, processes and routes audio across multiple zones. It can send different audio sources to different areas of a stadium, auditorium or house of worship and apply EQ, delay and limiting to individual outputs.
How many Dante channels does the Dynacord MXE5-64 support?
The MXE5-64 supports 64 Dante inputs and 64 Dante outputs at 48 or 96 kHz. With its 12 analog mic/line inputs and 8 analog line outputs, it provides a 76-input × 72-output audio matrix. It also supports AES67 network audio.
What software is used to configure the Dynacord MXE5-64?
Use Dynacord SONICUE Sound System Software to configure audio routing, build the DSP signal flow and design operator controls. The built-in TaskEngine handles automation such as scheduled actions and scene changes.
Can the MXE5-64 connect to existing microphones and amplifiers?
Yes. Its 12 balanced mic/line inputs accept microphones and line-level sources, and its 8 balanced line outputs can feed external amplifiers or powered speakers. Passive loudspeakers require a separate power amplifier.
What is the difference between the Dynacord MXE5 and MXE5-64?
The MXE5 has a 24 × 24 audio matrix, while the MXE5-64 has a 76 × 72 matrix with 64 × 64 dedicated Dante channels. Both have 12 analog mic/line inputs and 8 analog line outputs. The MXE5-64 is the better fit when the design requires more network audio channels.
Can the Dynacord MXE5-64 control audio in multiple zones independently?
Yes. The MXE5-64 can route different audio sources to different zones. For example, an auditorium can play programme audio in the main hall and background music in the lobby. SONICUE lets you create operator controls for each zone’s source and volume.
Who is an authorized Dynacord distributor in Pakistan?

ESCO (Electronic Security Company) is an authorized Dynacord distributor in Pakistan. Contact ESCO for the current Dynacord MXE5-64 price, stock availability, lead time or a project quotation.

Chat on WhatsApp
WhatsApp